{"product_id":"audiocontrol-epic1000","title":"AudioControl EPIC1000","description":"\u003ch2\u003eAudioControl EPIC1000 1000W RMS Monoblock Subwoofer Amplifier\u003c\/h2\u003e\n\u003cp\u003eGive your subwoofer dedicated power in a compact installation with the AudioControl EPIC1000. This Class D monoblock delivers up to 1,000W RMS at 1 ohm and includes an ACR-E remote level control, adjustable bass boost, and low-pass and subsonic filters to help match bass output to your speakers and enclosure.\u003c\/p\u003e\n\u003ch3\u003eRMS Power by Impedance\u003c\/h3\u003e\n\u003cp\u003eAudioControl specifies the following continuous output at \u003cstrong\u003e14.4V\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4 ohms:\u003c\/strong\u003e 400W RMS × 1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2 ohms:\u003c\/strong\u003e 700W RMS × 1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 ohm:\u003c\/strong\u003e 1,000W RMS × 1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe 1,000W rating applies at 1 ohm, not at every speaker load. Match the subwoofer's RMS handling and final wired impedance to the appropriate rating. A single EPIC1000 is stable down to 1 ohm; do not wire below that minimum.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStrapped operation:\u003c\/strong\u003e AudioControl lists 2,000W RMS × 1 at 2 ohms for a correctly configured strapped pair. That requires two amplifiers and the manufacturer's specified wiring and setup. It is not the output of one EPIC1000.\u003c\/p\u003e\n\u003ch3\u003eFilters and Bass Control\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-pass filter:\u003c\/strong\u003e 40–180Hz, 12dB\/octave Linkwitz-Riley\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubsonic filter:\u003c\/strong\u003e Off–50Hz, 12dB\/octave Linkwitz-Riley\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEPICBoost:\u003c\/strong\u003e Adjustable 30–80Hz center frequency with 0–12dB gain\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded ACR-E remote:\u003c\/strong\u003e Convenient subwoofer-level adjustment from the driver's seat\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSet the low-pass filter to blend the subwoofer with your speakers and match the subsonic setting to the enclosure, particularly in a ported system. Bass boost increases demand on the amplifier and subwoofer. Start conservatively and establish correct gain settings before adding boost.\u003c\/p\u003e\n\u003ch3\u003eEpicenter Link: Processor Sold Separately\u003c\/h3\u003e\n\u003cp\u003eThe included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. \u003cstrong\u003eThe Epicenter processor is sold separately; the EPIC1000 does not include built-in Epicenter bass restoration.\u003c\/strong\u003e EPICBoost adjusts bass already in the signal and is not the same function as harmonic bass restoration.\u003c\/p\u003e\n\u003ch3\u003eInstallation and Protection\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCompact, thermally efficient Class D design\u003c\/li\u003e\n\u003cli\u003eDirect-wire power and speaker terminals with hex screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\/ground terminal wire gauge:\u003c\/strong\u003e 4 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpeaker terminal wire gauge:\u003c\/strong\u003e 8 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer-recommended fuse:\u003c\/strong\u003e 100A\u003c\/li\u003e\n\u003cli\u003eSmart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eUse suitable power and ground wiring, proper battery-side circuit protection, a sound ground connection, and adequate ventilation. Fuse selection must also protect the installed wire. Check the vehicle's charging and battery capacity before planning sustained high-output use; protection circuits are not a substitute for correct installation.\u003c\/p\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLine-level input range:\u003c\/strong\u003e 500mV–12V RMS, per AudioControl's current specification page\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 10–190Hz, ±1dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal-to-noise ratio:\u003c\/strong\u003e 92.1dBA, referenced to 400W at 4 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChassis dimensions:\u003c\/strong\u003e 9.41 inches long × 6.1 inches wide × 2.01 inches high\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrapping capability:\u003c\/strong\u003e Yes, following the manufacturer's instructions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEpicenter Link:\u003c\/strong\u003e Yes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOlder AudioControl materials list a 6V maximum input rather than 12V. Confirm the documentation supplied with your unit before selecting a high-voltage source. These are line-level input specifications, not a guarantee of compatibility with every factory speaker-level signal. Factory-radio installations may require a separate signal converter or vehicle-specific interface.\u003c\/p\u003e\n\u003cp\u003eGeneral series copy cites a 91dB-plus signal-to-noise ratio and approximately 0.5–1A idle draw. Idle draw is not the current needed at rated output; use the model-specific specifications above and plan power wiring for actual operating demand.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAudioControl EPIC1000 amplifier\u003c\/li\u003e\n\u003cli\u003eWrench and screws\u003c\/li\u003e\n\u003cli\u003eACR-E remote level control and cable\u003c\/li\u003e\n\u003cli\u003eEpicenter Link 1-meter harness\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0581\/2240\/3900\/files\/EPIC2000_1500_1000_750_500qsg_rev-g.pdf?v=1755033512\"\u003eManual\u003c\/a\u003e and warranty documentation\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSubwoofers, enclosure, Epicenter processor, power wiring, fuse hardware, and any additional signal-integration parts are sold separately.\u003c\/p\u003e\n\u003ch3\u003eLocal Installation in Killeen, Texas\u003c\/h3\u003e\n\u003cp\u003eBest Auto Sound \u0026amp; Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching your subwoofer, verifying final impedance, and planning wiring and tuning. Installation and any additional required parts are quoted separately.\u003c\/p\u003e","brand":"AudioControl","offers":[{"title":"Default Title","offer_id":71174321307761,"sku":null,"price":239.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/4884\/5937\/files\/Screenshot_14-11-2026_12226_www.stingerdealer.com.jpg?v=1794680610","url":"https:\/\/12volttoys.com\/products\/audiocontrol-epic1000","provider":"Best Auto Sound \u0026 Security","version":"1.0","type":"link"}