AudioControl EPIC2000

AudioControl EPIC2000

$379.99
Sale price  $379.99 Regular price 
Skip to product information
AudioControl EPIC2000

AudioControl EPIC2000

$379.99
Sale price  $379.99 Regular price 

AudioControl EPIC2000 2000W RMS Monoblock Subwoofer Amplifier

Power a demanding subwoofer system with the AudioControl EPIC2000, a compact Class D monoblock rated for up to 2,000W RMS at 1 ohm. Adjustable low-pass and subsonic filters, EPICBoost bass adjustment, and the included ACR-E remote level control help you tailor bass output to your speakers and enclosure.

RMS Power by Impedance

AudioControl specifies the following continuous output at 14.4V:

  • 4 ohms: 800W RMS × 1
  • 2 ohms: 1,400W RMS × 1
  • 1 ohm: 2,000W RMS × 1

The 2,000W rating applies at 1 ohm, not at every impedance or supply voltage. Match your subwoofer system's RMS handling and final wired load to the appropriate rating. A single EPIC2000 is stable down to 1 ohm; do not wire below that minimum.

Strapped operation: AudioControl lists 4,000W RMS × 1 at 2 ohms for a correctly configured strapped pair. This requires two amplifiers and the manufacturer's specified setup; it is not the output of one EPIC2000.

Filters and Bass Control

  • Low-pass filter: 40–180Hz, 12dB/octave Linkwitz-Riley
  • Subsonic filter: Off–50Hz, 12dB/octave Linkwitz-Riley
  • EPICBoost: Variable 30–80Hz center frequency with 0–12dB gain
  • ACR-E remote level control: Included with cable

Set the low-pass filter to blend the subwoofer with your speakers and match the subsonic setting to your enclosure, especially in a ported system. Bass boost increases amplifier and subwoofer demand. Establish correct gain and crossover settings before adding boost.

Power Wiring and Protection

  • Power/ground wire size: 1/0 AWG, listed by AudioControl as 0/1 AWG
  • Speaker terminal wire gauge: 4 AWG
  • Manufacturer-recommended fuse: 200A
  • Direct-wire terminals with hex screws
  • Thermally efficient Class D design
  • Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature

Use the EPIC2000-specific wiring specifications above, not the smaller 4-gauge power/8-gauge speaker figures found in generic EPIC-series promotional copy. Have the complete power-wire run, battery-side fuse protection, grounding, charging capacity, and ventilation planned for the installation. Fuse selection must also protect the installed wire.

A 2,000W system can place substantial demand on the vehicle's electrical system. Charging or battery upgrades may be needed depending on the vehicle and use. Protection circuits do not replace adequate voltage, correct wiring, or safe gain adjustment.

Epicenter Link: Processor Sold Separately

The included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. The processor is sold separately, and the EPIC2000 does not include built-in Epicenter bass restoration. EPICBoost is bass equalization, not the same function as harmonic bass restoration.

Technical Specifications

  • Line-level input range: 500mV–12V RMS, per AudioControl's current product specifications
  • Frequency response: 10–190Hz, ±1dB
  • Signal-to-noise ratio: 92.9dBA, referenced to 800W at 4 ohms
  • Dimensions: 12.56 inches long × 6.1 inches wide × 2.01 inches high
  • Strapping capability: Yes, following the manufacturer's instructions
  • Epicenter Link: Yes

Older AudioControl materials specify a 6V maximum input rather than 12V. Check the documentation supplied with your unit before selecting a high-voltage source. These are line-level input specifications; do not assume compatibility with every factory speaker-level signal. A factory-radio installation may require a separate signal converter or vehicle-specific interface.

General series copy cites a 91dB-plus signal-to-noise ratio and approximately 0.5–1A idle draw. Idle draw is not the current required at rated output. Use the model-specific specifications and actual system demand when planning the installation.

What's Included

  • AudioControl EPIC2000 amplifier
  • Wrench and screws
  • ACR-E remote level control and cable
  • Epicenter Link 1-meter harness
  • Manual and warranty documentation

Subwoofers, enclosure, Epicenter processor, power wiring, fuse hardware, electrical upgrades, and any additional integration parts are sold separately.

Local Installation in Killeen, Texas

Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching your subwoofers, confirming final impedance, and planning electrical support and tuning. Installation and any additional required parts are quoted separately.

Recommended products you may also like