AudioControl EPIC4000
AudioControl EPIC4000 4000W RMS Monoblock Competition Amplifier
Build a high-output subwoofer system around the AudioControl EPIC4000, a Class D monoblock rated for up to 4,000W RMS at 1 ohm. Adjustable low-pass and subsonic filters, EPICBoost bass adjustment, and an included ACR-E remote level control let you tailor bass output to your subwoofers, enclosure, and listening preferences.
This is a high-current amplifier that requires a carefully planned electrical system, not a basic amplifier swap on stock wiring. Confirm charging capacity, battery support, final subwoofer impedance, and installation space before ordering.
Continuous RMS Power
AudioControl rates output at 14.4V and less than 1% THD:
- 4 ohms: 1,000W RMS × 1
- 2 ohms: 2,000W RMS × 1
- 1 ohm: 4,000W RMS × 1
The 4,000W figure applies at 1 ohm under the specified conditions, not at every impedance or supply voltage. Match the complete subwoofer load and RMS handling to the appropriate output rating. Do not wire below the specified 1-ohm minimum.
Required Electrical System and Mounting
- Dual power and ground connections: Two 0-gauge power wires and two 0-gauge ground wires are required.
- Wire material: Use high-quality 0-gauge OFC, oxygen-free copper, for all power and ground connections.
- Individual power-wire fusing: Install a 200A fuse on each 0-gauge power wire within 12 inches of its battery connection.
- Alternator: AudioControl's minimum electrical-system guidance calls for a high-output alternator delivering 200A at idle.
- Big 3 upgrade: The manual recommends 0-gauge wiring for the battery-negative-to-chassis, engine-block-to-chassis, and alternator-output-to-battery-positive connections.
- Auxiliary battery: Install an additional battery near the amplifier; the manual recommends at least 90Ah capacity and 1,000 CCA.
- Auxiliary-battery connections: The manual specifies dual 0-gauge OFC power and ground cables run directly between the main and auxiliary battery.
- Mounting: Do not mount the amplifier to a subwoofer enclosure. Use a secure location with appropriate ventilation and wiring clearance.
Have a qualified installer design the complete charging, battery, grounding, and circuit-protection layout for your vehicle. The specification table lists 200A × 2 / 400A × 1 as its fuse rating, but the installation instructions specifically call for a 200A fuse on each of the two power wires. Do not substitute one fuse for individual wire protection without an appropriately engineered distribution layout.
Filters, Bass Control, and Protection
- Low-pass filter: 40–180Hz, 12dB/octave Linkwitz-Riley
- Subsonic filter: Off–50Hz, 12dB/octave Linkwitz-Riley
- EPICBoost: Variable 30–80Hz center frequency with 0–12dB gain
- ACR-E remote level control: Included with cable
- Smart auto-reset protection circuit
- Solid power and speaker terminals with hex screws
- Thermally efficient, high-current Class D design
Set the subsonic filter for the subwoofer and enclosure, especially in a vented system. Bass boost increases demand and should be used conservatively after correct gain and crossover setup. Protection circuits do not guarantee protection from incorrect wiring, inadequate voltage, clipping, or an unsuitable speaker load.
Epicenter Link: Bass Processor Sold Separately
The included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. The EPIC4000 does not include an Epicenter processor or built-in Epicenter bass restoration. EPICBoost is bass equalization, not the same function as harmonic bass restoration.
The Link's referenced 1A fuse protection concerns the processor connection; it is not the amplifier's main power-wire fuse rating. The high-current amplifier wiring requires the separate protection described above.
Technical Specifications
- Amplifier topology: Class D monoblock
- Line-level input range: 0.5–12Vrms
- Frequency response: 10–190Hz, ±1dB
- Signal-to-noise ratio: 104.8dBA, referenced to 1,000W at 4 ohms
- Power/ground wire gauge: 0 AWG, dual runs as specified above
- Speaker terminal wire gauge: 8 AWG
- Chassis dimensions: 21 × 6.1 × 2.04 inches, L × W × H
- Metric dimensions: 533 × 155 × 52mm
Dimensions exclude connectors. Allow additional clearance for terminals, cable bends, and ventilation. Factory-radio installations may need a separate compatible signal converter or vehicle-specific interface; confirm the source signal before connecting it to the line-level inputs.
What's Included
- AudioControl EPIC4000 monoblock amplifier
- Wrench and screws
- ACR-E remote level control and cable
- Epicenter Link 1-meter harness
- User manual
Subwoofers, enclosure, Epicenter processor, power wiring, fuse hardware, charging-system upgrades, auxiliary battery, and any additional integration parts are sold separately.
Local Installation in Killeen, Texas
Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 to plan electrical upgrades, subwoofer matching, mounting, and tuning before your installation. Installation and any additional required parts are quoted separately.