AudioControl EPIC500
AudioControl EPIC500 500W RMS Monoblock Subwoofer Amplifier
Add dedicated subwoofer power without giving up a large mounting area with the AudioControl EPIC500. This compact Class D monoblock delivers up to 500W RMS at 1 ohm and includes an ACR-E remote level control, so you can adjust subwoofer level from the driver's seat after the system is properly tuned.
RMS Power at Your Subwoofer's Impedance
AudioControl specifies the following continuous output at 14.4V and less than 1% THD:
- 4 ohms: 250W RMS × 1
- 2 ohms: 350W RMS × 1
- 1 ohm: 500W RMS × 1
The 500W rating is not available at every impedance. Match the subwoofer's RMS handling and final wired impedance to the appropriate rating. A single EPIC500 is stable down to a 1-ohm load.
Strapped operation: AudioControl lists 1,000W RMS × 1 at 2 ohms for a properly configured strapped pair. This requires two amplifiers and the manufacturer's specified setup; it is not the output of one EPIC500.
Filters and Bass Adjustment
- Low-pass filter: 40–180Hz, 12dB/octave Linkwitz-Riley
- Subsonic filter: Off–50Hz, 12dB/octave Linkwitz-Riley
- EPICBoost: Adjustable 30–80Hz center frequency with 0–12dB gain
- Remote level control: ACR-E and cable included
Set the low-pass filter to blend the subwoofer with your speakers and choose the subsonic setting for the enclosure and subwoofer. Bass boost adds demand to the amplifier and subwoofer; it is not a substitute for correct gain adjustment or sufficient clean power.
Epicenter Link: Processor Sold Separately
The included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. The amplifier does not include an Epicenter processor or built-in Epicenter bass restoration. The processor is purchased separately. EPICBoost is an adjustable bass boost, not the same function as bass restoration.
Installation and Protection
- Compact, thermally efficient Class D design
- Direct-wire terminals with hex screws
- Power/ground terminal wire size: 4 AWG
- Speaker terminal wire size: 8 AWG
- Manufacturer-recommended fuse: 80A
- Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature
Use suitable power and ground wiring, a proper ground connection, and correctly located circuit protection. Final fuse selection must also protect the installed wire. Leave room for ventilation and cable routing; protection circuits do not replace proper installation.
The specified inputs are line-level. A factory-radio installation may require a separate compatible line-output converter or vehicle-specific interface. Do not assume the 12V input-signal rating means it accepts every factory speaker-level signal.
Technical Specifications
- Line-level input range: 500mV–12V RMS
- Frequency response: 10–190Hz, ±1dB
- Published signal-to-noise specification: 94dBA, referenced to 400W at 4 ohms
- Dimensions: 5.9 inches long × 6.1 inches wide × 2.01 inches high
AudioControl's published signal-to-noise reference uses 400W at 4 ohms, while its EPIC500 output table specifies 250W at 4 ohms. The noise-test reference is not an additional power rating. General EPIC-series promotional figures such as “91dB+” and approximately 0.5–1A idle draw should not be confused with model-specific output ratings.
What's Included
- AudioControl EPIC500 amplifier
- Wrench and screws
- ACR-E remote level control and cable
- Epicenter Link 1-meter harness
- Manual and warranty documentation
Subwoofers, enclosures, Epicenter processors, power wiring, fuse hardware, and any additional integration parts are sold separately.
Local Installation in Killeen, Texas
Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching your subwoofer, confirming final impedance, and planning power wiring and tuning. Installation and any additional required parts are quoted separately.