A black AudioControl EPICBIGfour-channel power amplifier with a brushed metal finish, featuring white branding and port connectors on the sides, shown on a plain white background.

AudioControl EPICBIGFOUR

$259.99
Sale price  $259.99 Regular price 
Skip to product information
A black AudioControl EPICBIGfour-channel power amplifier with a brushed metal finish, featuring white branding and port connectors on the sides, shown on a plain white background.

AudioControl EPICBIGFOUR

$259.99
Sale price  $259.99 Regular price 

AudioControl EPICBIGFOUR 1400W RMS 4-Channel Class D Amplifier

Give a demanding speaker system dedicated power with the AudioControl EPICBIGFOUR. This compact Class D amplifier delivers 200W RMS per channel at 4 ohms or 350W RMS per channel at 2 ohms, with high-pass and low-pass filtering for flexible system design and an included ACR-E remote level control.

RMS Power by Configuration

AudioControl specifies continuous output at 14.4V:

  • 4-ohm stereo: 200W RMS × 4
  • 2-ohm stereo: 350W RMS × 4
  • 4-ohm bridged: 650W RMS × 2

The 1,400W figure is the combined output of four channels at 2 ohms, not power per channel. Use the published 650W-per-bridged-pair rating rather than assuming bridged output from the stereo figures. Match each speaker's RMS handling and final impedance to the appropriate configuration.

Use no lower than 2 ohms per channel in stereo or 4 ohms per bridged pair. Follow the manufacturer's bridge wiring instructions. This is a four-channel amplifier, not a monoblock.

High-Pass and Low-Pass Crossover Control

  • High-pass filter: Off or 50–5,000Hz, 12dB/octave Linkwitz-Riley
  • Low-pass filter: Off or 50–5,000Hz, 12dB/octave Linkwitz-Riley
  • Range multiplier: The manual describes 50–500Hz adjustment at ×1 and 500–5,000Hz at ×10

The extended range supports properly designed active speaker systems as well as conventional filtered installations. For example, the manual explains that a 400Hz dial setting becomes 4kHz when the appropriate ×10 range button is engaged. Always check the range switches before tuning.

Select crossover frequencies and slopes for the specific drivers, not simply the amplifier's available range. Tweeters require suitable filtering and conservative output adjustment. If bridging for a subwoofer, set an appropriate low-pass filter and confirm the final load and enclosure requirements.

Included Remote and Construction

  • ACR-E remote level control and cable included
  • Thermally efficient, high-current Class D design
  • Direct-wire power and speaker terminals with hex screws
  • Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature

Set amplifier gain to match the source signal rather than using it as a volume control. Use the included remote according to the channel-routing instructions in the manual. Protection circuits do not replace correct wiring, ventilation, or safe gain and crossover settings.

Technical Specifications

  • Line-level input range: 500mV–12V RMS
  • Frequency response: 10Hz–22kHz, ±1dB
  • Signal-to-noise ratio: 89dBA, referenced to 200W at 4 ohms
  • Power/ground wire gauge: 4 AWG
  • Speaker terminal wire gauge: 8 AWG
  • Manufacturer-recommended fuse: 150A
  • Dimensions: 10.56 inches long × 6.1 inches wide × 2.01 inches high

Plan the complete power-wire run, ground connection, battery-side circuit protection, charging capacity, and ventilation for the system. The recommended amplifier fuse rating does not override the need to protect the installed wire for its size, material, and run length.

The specified inputs are line-level. A factory-radio installation may require a separate compatible signal converter or vehicle-specific interface. Do not assume that the 12V input-signal rating establishes compatibility with every factory speaker-level output.

Series promotional copy references approximately 0.5–1A idle draw. Idle draw is not the current required at rated output; size the electrical installation for actual operating demand.

Epicenter Integration

An external Epicenter bass-restoration processor is sold separately; this amplifier does not include built-in Epicenter bass restoration. The original listing references Epicenter Link compatibility, but a Link harness is not listed among the included components. Confirm the required connection method and accessories for the specific processor and signal routing before planning that installation.

What's Included

  • AudioControl EPICBIGFOUR amplifier
  • Wrench and screws
  • ACR-E remote level control and cable
  • Manual and warranty documentation

Speakers, subwoofers, external processors, power wiring, fuse hardware, signal cables, and any additional installation or integration parts are sold separately.

Local Installation in Killeen, Texas

Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching speaker power, choosing channel configurations, and planning active crossovers, wiring, and tuning. Installation and any additional required parts are quoted separately.

Recommended products you may also like