{"product_id":"audiocontrol-epicbigfour","title":"AudioControl EPICBIGFOUR","description":"\u003ch2\u003eAudioControl EPICBIGFOUR 1400W RMS 4-Channel Class D Amplifier\u003c\/h2\u003e\n\u003cp\u003eGive a demanding speaker system dedicated power with the AudioControl EPICBIGFOUR. This compact Class D amplifier delivers 200W RMS per channel at 4 ohms or 350W RMS per channel at 2 ohms, with high-pass and low-pass filtering for flexible system design and an included ACR-E remote level control.\u003c\/p\u003e\n\u003ch3\u003eRMS Power by Configuration\u003c\/h3\u003e\n\u003cp\u003eAudioControl specifies continuous output at \u003cstrong\u003e14.4V\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-ohm stereo:\u003c\/strong\u003e 200W RMS × 4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2-ohm stereo:\u003c\/strong\u003e 350W RMS × 4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-ohm bridged:\u003c\/strong\u003e 650W RMS × 2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe 1,400W figure is the combined output of four channels at 2 ohms, not power per channel. Use the published 650W-per-bridged-pair rating rather than assuming bridged output from the stereo figures. Match each speaker's RMS handling and final impedance to the appropriate configuration.\u003c\/p\u003e\n\u003cp\u003eUse no lower than 2 ohms per channel in stereo or 4 ohms per bridged pair. Follow the manufacturer's bridge wiring instructions. This is a four-channel amplifier, not a monoblock.\u003c\/p\u003e\n\u003ch3\u003eHigh-Pass and Low-Pass Crossover Control\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-pass filter:\u003c\/strong\u003e Off or 50–5,000Hz, 12dB\/octave Linkwitz-Riley\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-pass filter:\u003c\/strong\u003e Off or 50–5,000Hz, 12dB\/octave Linkwitz-Riley\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRange multiplier:\u003c\/strong\u003e The manual describes 50–500Hz adjustment at ×1 and 500–5,000Hz at ×10\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe extended range supports properly designed active speaker systems as well as conventional filtered installations. For example, the manual explains that a 400Hz dial setting becomes 4kHz when the appropriate ×10 range button is engaged. Always check the range switches before tuning.\u003c\/p\u003e\n\u003cp\u003eSelect crossover frequencies and slopes for the specific drivers, not simply the amplifier's available range. Tweeters require suitable filtering and conservative output adjustment. If bridging for a subwoofer, set an appropriate low-pass filter and confirm the final load and enclosure requirements.\u003c\/p\u003e\n\u003ch3\u003eIncluded Remote and Construction\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eACR-E remote level control and cable included\u003c\/li\u003e\n\u003cli\u003eThermally efficient, high-current Class D design\u003c\/li\u003e\n\u003cli\u003eDirect-wire power and speaker terminals with hex screws\u003c\/li\u003e\n\u003cli\u003eSmart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSet amplifier gain to match the source signal rather than using it as a volume control. Use the included remote according to the channel-routing instructions in the manual. Protection circuits do not replace correct wiring, ventilation, or safe gain and crossover settings.\u003c\/p\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLine-level input range:\u003c\/strong\u003e 500mV–12V RMS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 10Hz–22kHz, ±1dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal-to-noise ratio:\u003c\/strong\u003e 89dBA, referenced to 200W at 4 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\/ground wire gauge:\u003c\/strong\u003e 4 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpeaker terminal wire gauge:\u003c\/strong\u003e 8 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer-recommended fuse:\u003c\/strong\u003e 150A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions:\u003c\/strong\u003e 10.56 inches long × 6.1 inches wide × 2.01 inches high\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003ePlan the complete power-wire run, ground connection, battery-side circuit protection, charging capacity, and ventilation for the system. The recommended amplifier fuse rating does not override the need to protect the installed wire for its size, material, and run length.\u003c\/p\u003e\n\u003cp\u003eThe specified inputs are line-level. A factory-radio installation may require a separate compatible signal converter or vehicle-specific interface. Do not assume that the 12V input-signal rating establishes compatibility with every factory speaker-level output.\u003c\/p\u003e\n\u003cp\u003eSeries promotional copy references approximately 0.5–1A idle draw. Idle draw is not the current required at rated output; size the electrical installation for actual operating demand.\u003c\/p\u003e\n\u003ch3\u003eEpicenter Integration\u003c\/h3\u003e\n\u003cp\u003eAn external Epicenter bass-restoration processor is sold separately; this amplifier does not include built-in Epicenter bass restoration. The original listing references Epicenter Link compatibility, but a Link harness is not listed among the included components. Confirm the required connection method and accessories for the specific processor and signal routing before planning that installation.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAudioControl EPICBIGFOUR amplifier\u003c\/li\u003e\n\u003cli\u003eWrench and screws\u003c\/li\u003e\n\u003cli\u003eACR-E remote level control and cable\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0581\/2240\/3900\/files\/EPICBIGFOUR_qsg_Rev_D_030426.pdf?v=1772649909\"\u003eManual\u003c\/a\u003e and warranty documentation\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSpeakers, subwoofers, external processors, power wiring, fuse hardware, signal cables, and any additional installation or integration parts are sold separately.\u003c\/p\u003e\n\u003ch3\u003eLocal Installation in Killeen, Texas\u003c\/h3\u003e\n\u003cp\u003eBest Auto Sound \u0026amp; Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching speaker power, choosing channel configurations, and planning active crossovers, wiring, and tuning. Installation and any additional required parts are quoted separately.\u003c\/p\u003e","brand":"AudioControl","offers":[{"title":"Default Title","offer_id":71190657532017,"sku":null,"price":259.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/4884\/5937\/files\/Screenshot_14-11-2026_143732_www.stingerdealer.com.jpg?v=1794688699","url":"https:\/\/12volttoys.com\/products\/audiocontrol-epicbigfour","provider":"Best Auto Sound \u0026 Security","version":"1.0","type":"link"}