AudioControl EPICFOUR
AudioControl EPICFOUR 800W RMS 4-Channel Class D Amplifier
Give your front and rear speakers dedicated amplifier power with the AudioControl EPICFOUR. This compact Class D amplifier delivers 100W RMS per channel at 4 ohms or 200W RMS per channel at 2 ohms, with bridged operation available for properly matched higher-power applications.
RMS Power by Configuration
AudioControl specifies continuous output at 14.4V:
- 4-ohm stereo: 100W RMS Ã 4
- 2-ohm stereo: 200W RMS Ã 4
- 4-ohm bridged: 400W RMS Ã 2
The 800W rating is total output at the specified configuration, not 800W per channel. Match each speaker's RMS handling and final impedance to the appropriate rating. Use no lower than 2 ohms per channel in stereo or 4 ohms per bridged pair. Follow AudioControl's bridge wiring instructions.
Flexible Speaker-System Power
Use four channels for compatible front and rear speakers, or bridge channel pairs for two suitable higher-power loads. This is a four-channel amplifier, not an EPIC-series monoblock. A bridged subwoofer installation needs an appropriate low-pass-filtered signal and properly matched speaker load; do not assume the standard high-pass controls provide subwoofer low-pass filtering.
High-Pass Filtering and Tuning
The published product specifications list 12dB/octave Linkwitz-Riley high-pass filters with Off and 50â500Hz adjustment. High-pass filtering reduces low-frequency content sent to speakers that are not designed to reproduce deep bass. Choose crossover settings based on the speakers and installation, not simply the amplifier's available range.
AudioControl's newer linked manual also references additional filter-range controls. Check the controls and manual supplied with your particular unit before planning an active speaker system; do not assume every revision has identical crossover options. Set gain to match the source signal, not as a substitute for a volume control.
Construction and Protection
- Compact, thermally efficient Class D design
- High-current operation with 2-ohm stereo stability
- Direct-wire power and speaker terminals with hex screws
- Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature
Protection circuits do not replace correct speaker wiring, adequate ventilation, a reliable ground, or safe gain settings. Leave room for cable routing and cooling when choosing the mounting location.
Technical Specifications
- Line-level input range: 500mVâ12V RMS, per AudioControl's current product page
- Frequency response: 10Hzâ22kHz, ±1dB
- Signal-to-noise ratio: 90.1dBA, referenced to 100W at 4 ohms
- Power/ground wire gauge: 4 AWG
- Speaker terminal wire gauge: 8 AWG
- Recommended fuse: 80A
- Dimensions: 9.41 inches long à 6.1 inches wide à 2.01 inches high
Older AudioControl materials list a 6V maximum input rather than 12V. Confirm the documentation supplied with your unit before connecting a high-voltage source. The specified inputs are line-level; a factory-radio installation may require a separate compatible signal converter or vehicle-specific interface.
The model-specific noise specification is 90.1dBA, rather than the generic â91dB+â series claim. Series promotional copy also references approximately 0.5â1A idle draw; idle draw is not the current required at rated output. Plan power wiring and fuse protection for actual system demand, and ensure the fuse also protects the installed wire.
What's Included
- AudioControl EPICFOUR amplifier
- Wrench and screws
- Manual and warranty documentation
Speakers, power wiring, fuse hardware, signal cables, and any additional installation or integration parts are sold separately. A remote bass knob is not listed among the included components.
Local Installation in Killeen, Texas
Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching speaker power, choosing channel configurations, and planning signal integration and tuning. Installation and any additional required parts are quoted separately.