{"product_id":"audiocontrol-epicsix","title":"AudioControl EPICSIX","description":"\u003ch2\u003eAudioControl EPICSIX 1200W RMS 6-Channel Class D Amplifier\u003c\/h2\u003e\n\u003cp\u003eBuild a flexible multi-speaker system around the AudioControl EPICSIX, a compact full-range Class D amplifier with six powered channels. It delivers 100W RMS per channel at 4 ohms or 200W RMS per channel at 2 ohms, with channel-specific crossovers and selected bridging options for more involved system designs.\u003c\/p\u003e\n\u003ch3\u003eRMS Power by Configuration\u003c\/h3\u003e\n\u003cp\u003eAudioControl specifies continuous output at \u003cstrong\u003e14.4V and less than 1% THD\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-ohm stereo:\u003c\/strong\u003e 100W RMS × 6\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2-ohm stereo:\u003c\/strong\u003e 200W RMS × 6\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-ohm bridged:\u003c\/strong\u003e 400W RMS × 2 using channel pairs 3\/4 and 5\/6\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe 1,200W rating is the combined output of six channels at 2 ohms, not power per channel. Match each speaker's RMS handling and final load to the selected configuration. Use no lower than 2 ohms per unbridged channel or 4 ohms per supported bridged pair.\u003c\/p\u003e\n\u003ch3\u003eImportant Channel and Bridging Restrictions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eChannels 1 and 2 cannot be bridged.\u003c\/strong\u003e Only channels 3\/4 and 5\/6 are specified as bridgeable pairs. Do not assume all adjacent speaker terminals form a bridgeable pair; the manual identifies a different physical terminal arrangement for channels 1\/2 versus channels 3–6.\u003c\/p\u003e\n\u003cp\u003eFollow AudioControl's terminal markings, input-mode settings, and wiring diagrams for your chosen layout. Six-channel, active three-way front-stage, five-channel, and selected bridged configurations are possible when the signal routing, crossovers, and speaker loads are planned correctly. These are alternative configurations, not additional outputs available simultaneously.\u003c\/p\u003e\n\u003ch3\u003eChannel-Specific Crossover Control\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-pass filters:\u003c\/strong\u003e Available on channels 1–6; Off or 50–5,000Hz\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-pass filters:\u003c\/strong\u003e Available on channels 3–6; published adjustment range 50–5,000Hz\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilter slope:\u003c\/strong\u003e 12dB\/octave Linkwitz-Riley\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eChannels 1\/2 have high-pass filtering only. Channels 3–6 add low-pass filtering for more flexible driver assignments. Check the manual's filter and range-switch settings before planning an active system.\u003c\/p\u003e\n\u003cp\u003eChoose crossover frequencies and slopes for the actual speakers. Tweeters need suitable filtering and conservative gain adjustment; the availability of a crossover does not guarantee protection at every setting. For a bridged subwoofer installation, confirm the final impedance and apply an appropriate low-pass signal and enclosure-specific filtering.\u003c\/p\u003e\n\u003ch3\u003eConstruction and Installation\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCompact, thermally efficient full-range Class D design\u003c\/li\u003e\n\u003cli\u003eHigh-current design with 2-ohm unbridged stability\u003c\/li\u003e\n\u003cli\u003eSmart auto-reset protection circuit\u003c\/li\u003e\n\u003cli\u003eSolid direct-wire power and speaker terminals with hex screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\/ground wire gauge:\u003c\/strong\u003e 4 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpeaker terminal wire gauge:\u003c\/strong\u003e 10 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer-recommended fuse:\u003c\/strong\u003e 125A\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003ePlan suitable power wiring, a reliable ground, battery-side circuit protection, ventilation, and charging capacity for the complete system. Fuse selection must also protect the installed wire for its material, size, and run length. Protection circuitry does not replace correct wiring or safe gain adjustment.\u003c\/p\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLine-level input range:\u003c\/strong\u003e 500mV–12V RMS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 10Hz–24kHz, ±3dB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal-to-noise ratio:\u003c\/strong\u003e 98dBA, referenced to 100W at 4 ohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions, W × L × H:\u003c\/strong\u003e 6.1 × 12.56 × 2.01 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMetric dimensions, W × L × H:\u003c\/strong\u003e 155 × 319 × 51mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe specified inputs are line-level. A factory-radio installation may require a separate compatible signal converter or vehicle-specific interface. Do not assume the 12V signal-input rating establishes compatibility with every factory speaker-level output.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAudioControl EPICSIX amplifier\u003c\/li\u003e\n\u003cli\u003eWrench and screws\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0581\/2240\/3900\/files\/EPICSIX_qsg_Rev_B_021126.pdf?v=1774555189\"\u003eUser manual\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSpeakers, subwoofers, power wiring, fuse hardware, signal cables, and any additional installation or integration parts are sold separately. A remote level control is not listed among the included components.\u003c\/p\u003e\n\u003ch3\u003eLocal Installation in Killeen, Texas\u003c\/h3\u003e\n\u003cp\u003eBest Auto Sound \u0026amp; Security offers local installation in Killeen, Texas. Call 254-213-0501 for help with channel assignments, active speaker layouts, bridging, wiring, and system tuning. Installation and any additional required parts are quoted separately.\u003c\/p\u003e","brand":"AudioControl","offers":[{"title":"Default Title","offer_id":71190674571377,"sku":null,"price":279.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/4884\/5937\/files\/Screenshot_14-11-2026_145254_www.stingerdealer.com.jpg?v=1794689690","url":"https:\/\/12volttoys.com\/products\/audiocontrol-epicsix","provider":"Best Auto Sound \u0026 Security","version":"1.0","type":"link"}