AudioControl EPIC1000
AudioControl EPIC1000 1000W RMS Monoblock Subwoofer Amplifier
Give your subwoofer dedicated power in a compact installation with the AudioControl EPIC1000. This Class D monoblock delivers up to 1,000W RMS at 1 ohm and includes an ACR-E remote level control, adjustable bass boost, and low-pass and subsonic filters to help match bass output to your speakers and enclosure.
RMS Power by Impedance
AudioControl specifies the following continuous output at 14.4V:
- 4 ohms: 400W RMS × 1
- 2 ohms: 700W RMS × 1
- 1 ohm: 1,000W RMS × 1
The 1,000W rating applies at 1 ohm, not at every speaker load. Match the subwoofer's RMS handling and final wired impedance to the appropriate rating. A single EPIC1000 is stable down to 1 ohm; do not wire below that minimum.
Strapped operation: AudioControl lists 2,000W RMS × 1 at 2 ohms for a correctly configured strapped pair. That requires two amplifiers and the manufacturer's specified wiring and setup. It is not the output of one EPIC1000.
Filters and Bass Control
- Low-pass filter: 40–180Hz, 12dB/octave Linkwitz-Riley
- Subsonic filter: Off–50Hz, 12dB/octave Linkwitz-Riley
- EPICBoost: Adjustable 30–80Hz center frequency with 0–12dB gain
- Included ACR-E remote: Convenient subwoofer-level adjustment from the driver's seat
Set the low-pass filter to blend the subwoofer with your speakers and match the subsonic setting to the enclosure, particularly in a ported system. Bass boost increases demand on the amplifier and subwoofer. Start conservatively and establish correct gain settings before adding boost.
Epicenter Link: Processor Sold Separately
The included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. The Epicenter processor is sold separately; the EPIC1000 does not include built-in Epicenter bass restoration. EPICBoost adjusts bass already in the signal and is not the same function as harmonic bass restoration.
Installation and Protection
- Compact, thermally efficient Class D design
- Direct-wire power and speaker terminals with hex screws
- Power/ground terminal wire gauge: 4 AWG
- Speaker terminal wire gauge: 8 AWG
- Manufacturer-recommended fuse: 100A
- Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature
Use suitable power and ground wiring, proper battery-side circuit protection, a sound ground connection, and adequate ventilation. Fuse selection must also protect the installed wire. Check the vehicle's charging and battery capacity before planning sustained high-output use; protection circuits are not a substitute for correct installation.
Technical Specifications
- Line-level input range: 500mV–12V RMS, per AudioControl's current specification page
- Frequency response: 10–190Hz, ±1dB
- Signal-to-noise ratio: 92.1dBA, referenced to 400W at 4 ohms
- Chassis dimensions: 9.41 inches long × 6.1 inches wide × 2.01 inches high
- Strapping capability: Yes, following the manufacturer's instructions
- Epicenter Link: Yes
Older AudioControl materials list a 6V maximum input rather than 12V. Confirm the documentation supplied with your unit before selecting a high-voltage source. These are line-level input specifications, not a guarantee of compatibility with every factory speaker-level signal. Factory-radio installations may require a separate signal converter or vehicle-specific interface.
General series copy cites a 91dB-plus signal-to-noise ratio and approximately 0.5–1A idle draw. Idle draw is not the current needed at rated output; use the model-specific specifications above and plan power wiring for actual operating demand.
What's Included
- AudioControl EPIC1000 amplifier
- Wrench and screws
- ACR-E remote level control and cable
- Epicenter Link 1-meter harness
- Manual and warranty documentation
Subwoofers, enclosure, Epicenter processor, power wiring, fuse hardware, and any additional signal-integration parts are sold separately.
Local Installation in Killeen, Texas
Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching your subwoofer, verifying final impedance, and planning wiring and tuning. Installation and any additional required parts are quoted separately.