AudioControl EPIC1000

AudioControl EPIC1000

$239.99
Sale price  $239.99 Regular price 
Skip to product information
AudioControl EPIC1000

AudioControl EPIC1000

$239.99
Sale price  $239.99 Regular price 

AudioControl EPIC1000 1000W RMS Monoblock Subwoofer Amplifier

Give your subwoofer dedicated power in a compact installation with the AudioControl EPIC1000. This Class D monoblock delivers up to 1,000W RMS at 1 ohm and includes an ACR-E remote level control, adjustable bass boost, and low-pass and subsonic filters to help match bass output to your speakers and enclosure.

RMS Power by Impedance

AudioControl specifies the following continuous output at 14.4V:

  • 4 ohms: 400W RMS × 1
  • 2 ohms: 700W RMS × 1
  • 1 ohm: 1,000W RMS × 1

The 1,000W rating applies at 1 ohm, not at every speaker load. Match the subwoofer's RMS handling and final wired impedance to the appropriate rating. A single EPIC1000 is stable down to 1 ohm; do not wire below that minimum.

Strapped operation: AudioControl lists 2,000W RMS × 1 at 2 ohms for a correctly configured strapped pair. That requires two amplifiers and the manufacturer's specified wiring and setup. It is not the output of one EPIC1000.

Filters and Bass Control

  • Low-pass filter: 40–180Hz, 12dB/octave Linkwitz-Riley
  • Subsonic filter: Off–50Hz, 12dB/octave Linkwitz-Riley
  • EPICBoost: Adjustable 30–80Hz center frequency with 0–12dB gain
  • Included ACR-E remote: Convenient subwoofer-level adjustment from the driver's seat

Set the low-pass filter to blend the subwoofer with your speakers and match the subsonic setting to the enclosure, particularly in a ported system. Bass boost increases demand on the amplifier and subwoofer. Start conservatively and establish correct gain settings before adding boost.

Epicenter Link: Processor Sold Separately

The included 1-meter Epicenter Link harness simplifies connection to a compatible Epicenter bass-restoration processor. The Epicenter processor is sold separately; the EPIC1000 does not include built-in Epicenter bass restoration. EPICBoost adjusts bass already in the signal and is not the same function as harmonic bass restoration.

Installation and Protection

  • Compact, thermally efficient Class D design
  • Direct-wire power and speaker terminals with hex screws
  • Power/ground terminal wire gauge: 4 AWG
  • Speaker terminal wire gauge: 8 AWG
  • Manufacturer-recommended fuse: 100A
  • Smart auto-reset protection for output over-current, input over-voltage, input under-voltage, output DC offset, and over-temperature

Use suitable power and ground wiring, proper battery-side circuit protection, a sound ground connection, and adequate ventilation. Fuse selection must also protect the installed wire. Check the vehicle's charging and battery capacity before planning sustained high-output use; protection circuits are not a substitute for correct installation.

Technical Specifications

  • Line-level input range: 500mV–12V RMS, per AudioControl's current specification page
  • Frequency response: 10–190Hz, ±1dB
  • Signal-to-noise ratio: 92.1dBA, referenced to 400W at 4 ohms
  • Chassis dimensions: 9.41 inches long × 6.1 inches wide × 2.01 inches high
  • Strapping capability: Yes, following the manufacturer's instructions
  • Epicenter Link: Yes

Older AudioControl materials list a 6V maximum input rather than 12V. Confirm the documentation supplied with your unit before selecting a high-voltage source. These are line-level input specifications, not a guarantee of compatibility with every factory speaker-level signal. Factory-radio installations may require a separate signal converter or vehicle-specific interface.

General series copy cites a 91dB-plus signal-to-noise ratio and approximately 0.5–1A idle draw. Idle draw is not the current needed at rated output; use the model-specific specifications above and plan power wiring for actual operating demand.

What's Included

  • AudioControl EPIC1000 amplifier
  • Wrench and screws
  • ACR-E remote level control and cable
  • Epicenter Link 1-meter harness
  • Manual and warranty documentation

Subwoofers, enclosure, Epicenter processor, power wiring, fuse hardware, and any additional signal-integration parts are sold separately.

Local Installation in Killeen, Texas

Best Auto Sound & Security offers local installation in Killeen, Texas. Call 254-213-0501 for help matching your subwoofer, verifying final impedance, and planning wiring and tuning. Installation and any additional required parts are quoted separately.

Recommended products you may also like